HP 830 Unified Wired-WLAN Switch Series

Product overview

The HP 830 Unified Wired-WLAN Switch Series integrates both wireless controller and 1000 Mb/s Ethernet switch functions. The switch series provides 1000 Mb/s Ethernet ports, with each supporting a maximum power of up to 30 W PoE+ and IEEE 802.11a/b/g/n APs while delivering unified wired and wireless access control functions. The HP 830 24-Port PoE+ Unified Wired-WLAN Switch provides two 10GbE slots on the rear panel to relieve transmission bottleneck at the core of a WLAN network. The HP 830 Unified Wired-WLAN Switch Series are part of the HPN Mobility enterprise solution. This product set provides edge-to-core unified access and consistent WLAN services to small/medium branch offices for enterprises that are deploying the HP 10500/7500 20G Unified Wired-WLAN Module at their central (or main) office.
  • Unified wired and wireless services for branch offices
  • System-wide approach to WLAN reliability through Wi-Fi Clear Connect
  • PoE+ capability
  • Built-in IEEE 802.1X and portal authentication servers
  • 8-port and 24-port versions available

QuickSpecs

What's new

Integrates both wireless and Gb Ethernet switch functions, delivering unified access for small/medium branches, consistent user security, policy, QoS and RF optimization.

  • Flexible forwarding options with local drop off of traffic & policy based forwarding
  • Integrated wireless IPS and embedded firewall for role or SSID based access
  • Source address validation prevents IP address spoofing
  • Staged firmware upgrades
  • 802.11k and sFlow support

Management

  • Wi-Fi Clear Connect — provides a system-wide approach to help ensure WLAN reliability by proactively determining and adjusting to changing RF conditions and by identifying rogue activity, and optimizing WLAN performance by detecting interference from Wi-Fi and non-Wi-Fi sources using Spectrum Analysis capabilities built into the MSM430, MSM46x, and HP 425 access points.
  • Advanced radio resource management
    • Automatic radio power adjustments — include real-time power adjustments based on changing environmental conditions and signal coverage adjustments
    • Automatic radio channel — provides intelligent channel switching and real-time interference detection
    • Intelligent client load balancing — balances the number of clients across multiple APs to optimize AP and client throughput
    • Airtime fairness — helps ensure equal RF transmission time for wireless clients
  • Spectrum Analysis (requires HP MSM430, MSM46x, or HP 425 Access Points)
    • Signal detection/classification — identifies source of RF interference, for example, Bluetooth, cordless phones, and microwave ovens
    • Evaluation of channel quality — helps detect severe channel degradation and improves the reporting of poor RF performance
  • Band Navigation — enables automatic redirection of 5 GHz-capable clients to the less-congested 5 GHz spectrum
  • Enterprise network management — is provided by HP Intelligent Management Center (IMC) Platform software and the IMC Wireless Services Manager Software Module, which effectively integrate traditionally disparate management tools into one easy-to-use interface
  • Secure controller management — manages the controller securely from a single location with IMC or any other SNMP management station; controller supports SNMPv3 as well as SSHv2 and SSL for secure CLI and Web management; console port is available as a pass-through to the switch console function

Quality of Service (QoS)

  • IEEE 802.1p prioritization — delivers data to devices based on the priority and type of traffic
  • Class of Service (CoS) — sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source port, and DiffServ

Security

  • Web-based authentication — provides a browser-based environment to authenticate clients that do not support the IEEE 802.1X supplicant
  • IEEE 802.1X and RADIUS network logins — supports port-based and SSID-based IEEE 802.1X authentication and accounting
  • WEP, WPA2, or WPA encryption — can be deployed at the AP to lock out unauthorized wireless access by authenticating users prior to granting network access; robust Advanced Encryption Standard (AES) or Temporal Key Integrity Protocol (TKIP) encryption secures the data integrity of wireless traffic
  • Integrated intrusion detection system (IDS) support — provides support for hybrid and dedicated modes; detects flood, spoofing, and weak IV attacks; displays statistics (events) and history; supports configuration of detection policies
  • Media access control (MAC) authentication — provides simple authentication based on a user's MAC address; supports local or RADIUS-based authentication
  • Secure user isolation — virtual AP services enable network administrators to provide specific services for different user groups, allowing effective resource sharing, and simplifying network maintenance and management
  • Secure access by location — AP location-based user access control helps ensure that wireless users can access and authenticate only to preselected APs, enabling system administrators to control the locations where a wireless user can access the network
  • Endpoint Admission Defense — integrated wired and wireless Endpoint Admission Defense (EAD) helps ensure that only wireless clients who comply with mandated enterprise security policies can access the network, reducing threat levels caused by infected wireless clients and improving the overall security of the wireless network
  • Public Key Infrastructure (PKI) — is used to control access
  • Authentication, authorization, and accounting (AAA) — uses an embedded authentication server or external AAA server for local users

Connectivity

  • IEEE 802.3at Power over Ethernet (PoE+) — provides 30 W of support per port for PoE+-capable devices such as IP phones, wireless access points, and security cameras, as well as any IEEE 802.3af-compliant end device; eliminates the cost of additional electrical cabling that would be needed in IP phone and WLAN deployments; the HP 830 8-Port PoE+ Unified Wired-WLAN Switch supports up to 5 ports at 30 W; the 24-port model can support up to 24 ports at up to 30 W depending on the power source
  • Loopback — supports internal loopback testing for maintenance purposes and an increase in availability; loopback detection protects against incorrect cabling or network configurations and can be enabled on a per-port or per-VLAN basis for added flexibility
  • IPv6
    • IPv6 host — enables controllers to be managed and deployed at the IPv6 network's edge
    • Dual stack (IPv4 and IPv6) — transitions customers from IPv4 to IPv6, supporting connectivity for both protocols
    • MLD snooping — directs IPv6 multicast traffic to the appropriate interface, preventing traffic flooding
    • IPv6 ACL/QoS — supports ACL and QoS for IPv6 network traffic

Performance

  • Flexible forwarding modes — supports both distributed and centralized forwarding mode; in a wireless network using centralized forwarding, all wireless traffic is sent to the HP 830 Unified Wired-WLAN Switch for processing; if the distributed mode is configured, authenticated clients can continue to access local resources in the event that connectivity to the HP 830 Unified Wired-WLAN Switch is lost
  • Fast roaming — supports Layer 3 roaming and fast roaming, satisfying the most demanding voice service requirements

Scalability

  • Pay as you grow — license upgrades allow you to increase support for additional access points without the need to buy additional costly hardware and use additional valuable space in a rack

Resiliency and high availability

  • High reliability — supports N+1 and N+N backup

Layer 2 switching

  • VLAN support and tagging — supports IEEE 802.1Q with 4,094 simultaneous VLAN IDs
  • Spanning Tree Protocol (STP) — supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE 802.1s Multiple Spanning Tree Protocol (MSTP)
  • Port mirroring — duplicates port traffic (ingress and egress) to a local or remote monitoring port
  • Jumbo packet support — supports frame sizes up to 9K byte (switch) and up to 4K byte (controller) to improve the performance of large data transfers

Layer 3 routing

  • Routing Information Protocol (RIP) — provides RIPv1 and RIPv2 routing
  • Static IP routing — provides manually configured routing for both IPv4 and IPv6 networks

Comprehensive portfolio

  • Access point support — includes HP MSM430, MSM460, MSM466, MSM466-R, HP 425, WA2620, WA2620E, WA2612, and WA2610E models

Warranty and support

  • Lifetime Warranty 2.0 — advance hardware replacement for as long as you own the product with next-business-day delivery (available in most countries)†
  • Electronic and telephone support (for Lifetime Warranty 2.0) — limited 24x7 telephone support is available from HP for the first 3 years; limited electronic and business hours telephone support is available from HP for the entire warranty period; to reach our support centers, refer to www.hp.com/networking/contact-support; for details on the duration of support provided with your product purchase, refer to www.hp.com/networking/warrantysummary
  • Software releases — includes all offered software releases for as long as you own the product; to find software for your product, refer to www.hp.com/networking/support; for details on the software releases available with your product purchase, refer to www.hp.com/networking/warrantysummary
HP 830 24-Port PoE+ Unified Wired-WLAN Switch (JG640A) HP 830 8-Port PoE+ Unified Wired-WLAN Switch (JG641A)
Ports
24 RJ-45 auto-negotiating 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T)

Media Type: Auto-MDIX

Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

4 SFP dual-personality ports

Duplex: full only

(4 10/100/1000BASE-T and 1000BASE-X Gigabit Ethernet combination)

2 extended module slots

1 RJ-45 serial console port

8 RJ-45 dual-personality 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T)

Media Type: Auto-MDIX

Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

2 SFP 1000 Mbps ports

1 RJ-45 serial console port

Physical characteristics
17.32(w) x 16.89(d) x 1.72(h) in (44 x 42.9 x 4.36 cm) (1U height) 17.32(w) x 10.63(d) x 1.72(h) in (44 x 27 x 4.36 cm) (1U height)
Weight 15.87 lb (7.2 kg) 8.82 lb (4 kg)
Memory and processor
Processor Dual core @ 750 MHz, 1 GB flash, 512 MB DDR2 SDRAM Dual core @ 750 MHz, 1 GB compact flash, 512 MB DDR2 SDRAM
Mounting
EIA-standard 19-inch telco rack or equipment cabinet (hardware included) EIA-standard 19-inch telco rack or equipment cabinet (hardware included)
Performance
Switch fabric speed 88 Gb/s 20 Gb/s
MAC address table size 8000 entries 8000 entries
Environment
Operating temperature 32°F to 113°F (0°C to 45°C) 32°F to 113°F (0°C to 45°C)
Operating relative humidity 5% to 95%, noncondensing 5% to 95%, noncondensing
Nonoperating/Storage temperature -40°F to 158°F (-40°C to 70°C) -40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage relative humidity 5% to 95%, noncondensing 5% to 95%, noncondensing
Electrical characteristics
Frequency 50/60 Hz 50/60 Hz
Maximum heat dissipation 307 BTU/hr (323.89 kJ/hr) 130 BTU/hr (137.15 kJ/hr)
Voltage 100-240 VAC 100-240 VAC
DC voltage -52 to -55 VDC
Maximum power rating 90 W 38 W
Idle power 53 W 28 W
PoE power 370 W 180 W
Notes Idle power is the actual power consumption of the device with no ports connected.
PoE power is the power supplied by the internal power supply. It is dependent on the type and quantity of power supplies and may be supplemented with the use of an external power supply (EPS).
Internal power supply delivers PoE+ to a maximum of 11 ports. PoE+ can be delivered to all 24 ports with the use of an optional redundant power system.
Idle power is the actual power consumption of the device with no ports connected.
PoE power is the power supplied by the internal power supply. It is dependent on the type and quantity of power supplies and may be supplemented with the use of an external power supply (EPS).
Internal power supply delivers PoE+ to a maximum of five ports.
Safety
UL 60950-1CAN/CSA 22.2 No. 60950-1IEC 60950-1EN 60950-1FDA 21 CFR Subchapter J UL 60950-1CAN/CSA 22.2 No. 60950-1IEC 60950-1EN 60950-1FDA 21 CFR Subchapter J
Features
Default supported APs: 24 :
Maximum supported APs: 60 (via the optional purchase of the 12-access point E-LTU) :
Maximum supported users: 1,000 :
Maximum supported users via local portal authentication: 1,000 :
Maximum supported users via local authentication: 1,000 :
Maximum supported configured SSIDs: 64 :
Maximum supported ACLs: 2,000 :
Supported MSM APs are automatically discovered, Comware firmware is loaded, and the APs can be fully managed. :
Default supported APs: 12 :
Maximum supported APs: 24 (via the optional purchase of the 12-access point E-LTU) :
Maximum supported users: 1,000 :
Maximum supported users via local portal authentication: 1,000 :
Maximum supported users via local authentication: 1,000 :
Maximum supported configured SSIDs: 64 :
Maximum supported ACLs: 2,000 :
Supported MSM APs are automatically discovered, Comware firmware is loaded, and the APs can be fully managed. :

Emissions

EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A; AS/NZS CISPR 22 Class A; EN 61000-3-2; EN 61000-3-3; VCCI-3 CLASS A; VCCI-4 CLASS A; ETSI EN 300 386; FCC Part 15 (CFR 47) CLASS A

Immunity

EN: EN 55024, CISPR24 & ETSI EN 300 386

Management

IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager; Telnet; HTTPS; RMON1; FTP; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB

Standards and protocols

General protocols
  • RFC 768 UDP
  • RFC 791 IP
  • RFC 792 ICMP
  • RFC 793 TCP
  • RFC 826 ARP
  • RFC 854 TELNET
  • RFC 855 Telnet Option Specification
  • RFC 858 Telnet Suppress Go Ahead Option
  • RFC 894 IP over Ethernet
  • RFC 950 Internet Standard Subnetting Procedure
  • RFC 959 File Transfer Protocol (FTP)
  • RFC 1122 Host Requirements
  • RFC 1141 Incremental updating of the Internet checksum
  • RFC 1144 Compressing TCP/IP headers for low-speed serial links
  • RFC 1256 ICMP Router Discovery Protocol (IRDP)
  • RFC 1305 NTPv3 (IPv4 only)
  • RFC 1321 The MD5 Message-Digest Algorithm
  • RFC 1334 PPP Authentication Protocols (PAP)
  • RFC 1350 TFTP Protocol (revision 2)
  • RFC 1812 IPv4 Routing
  • RFC 1944 Benchmarking Methodology for Network Interconnect Devices
  • RFC 1994 PPP Challenge Handshake Authentication Protocol (CHAP)
  • RFC 2104 HMAC: Keyed-Hashing for Message Authentication
  • RFC 2246 The TLS Protocol Version 1.0
  • RFC 2284 EAP over LAN
  • RFC 2644 Directed Broadcast Control
  • RFC 2864 The Inverted Stack Table Extension to the Interfaces Group MIB
  • RFC 2866 RADIUS Accounting
  • RFC 2869 RADIUS Extensions
  • RFC 3268 Advanced Encryption Standard (AES) Ciphersuites for Transport Layer Security (TLS)
  • RFC 3619 Ethernet Automatic Protection Switching (EAPS)
IP multicast
  • RFC 1112 IGMP
  • RFC 2236 IGMPv2
  • RFC 2934 Protocol Independent Multicast MIB for IPv4
  • RFC 4541 Considerations for Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) Snooping Switches
IPv6
  • RFC 1350 TFTP
  • RFC 1881 IPv6 Address Allocation Management
  • RFC 1887 IPv6 Unicast Address Allocation Architecture
  • RFC 1981 IPv6 Path MTU Discovery
  • RFC 2292 Advanced Sockets API for IPv6
  • RFC 2373 IPv6 Addressing Architecture
  • RFC 2375 IPv6 Multicast Address Assignments
  • RFC 2460 IPv6 Specification
  • RFC 2461 IPv6 Neighbor Discovery
  • RFC 2462 IPv6 Stateless Address Auto-configuration
  • RFC 2463 ICMPv6
  • RFC 2464 Transmission of IPv6 over Ethernet Networks
  • RFC 2465 Management Information Base for IP Version 6: Textual Conventions and General Group(partially support, only "IPv6 Interface Statistics table")
  • RFC 2466, Management Information Base for IP Version 6 - ICMPv6
  • RFC 2526 Reserved IPv6 Subnet Anycast Addresses
  • RFC 2553 Basic Socket Interface Extensions for IPv6
  • RFC 2563 ICMPv6
  • RFC 2925 Definitions of Managed Objects for Remote Ping, Traceroute, and Lookup Operations (Ping only)
  • RFC 3315 DHCPv6 (client and relay)
  • RFC 3363 DNS support
  • RFC 3484 Default Address Selection for IPv6
  • RFC 3493 Basic Socket Interface Extensions for IPv6
  • RFC 3513 IPv6 Addressing Architecture
  • RFC 3542 Advanced Sockets API for IPv6
  • RFC 3587 IPv6 Global Unicast Address Format
  • RFC 3596 DNS Extension for IPv6
  • RFC 4193, Unique Local IPv6 Unicast Addresses
  • RFC 4443 ICMPv6
  • RFC 4541 IGMP & MLD Snooping Switch
  • RFC 4861 IPv6 Neighbor Discovery
  • RFC 4862 IPv6 Stateless Address Auto-configuration
  • RFC 5095 Deprecation of Type 0 Routing Headers in IPv6
MIBs
  • RFC 1229 Interface MIB Extensions
  • RFC 1643 Ethernet MIB
  • RFC 1757 Remote Network Monitoring MIB
  • RFC 2011 SNMPv2 MIB for IP
  • RFC 2012 SNMPv2 MIB for TCP
  • RFC 2013 SNMPv2 MIB for UDP
  • RFC 2571 SNMP Framework MIB
  • RFC 2572 SNMP-MPD MIB
  • RFC 2613 SMON MIB
  • RFC 2863 The Interfaces Group MIB
  • RFC 2932IP (Multicast Routing MIB)
  • RFC 2933 IGMP MIB
Mobility
  • IEEE 802.11a High Speed Physical Layer in the 5 GHz Band
  • IEEE 802.11b Higher-Speed Physical Layer Extension in the 2.4 GHz Band
  • IEEE 802.11d Global Harmonization
  • IEEE 802.11e QoS enhancements
  • IEEE 802.11g Further Higher Data Rate Extension in the 2.4 GHz Band
  • IEEE 802.11h Dynamic Frequency Selection
  • IEEE 802.11i Medium Access Control (MAC) Security Enhancements
  • IEEE 802.11n WLAN Enhancements for Higher Throughput
  • Note: All of the above standards are now included in IEEE 802.11-2012
Network management
  • RFC 1155 Structure of Management Information
  • RFC 1905 SNMPv2 Protocol Operations
  • RFC 2573 SNMPv3 Applications
  • RFC 2574 SNMPv3 User-based Security Model (USM)
  • RFC 2575 VACM for SNMP
  • SNMPv1/v2c
QoS/CoS
  • RFC 2474 DS Field in the IPv4 and IPv6 Headers
  • RFC 2475 DiffServ Architecture
  • RFC 3168 The Addition of Explicit Congestion Notification (ECN) to IP
  • WiFi MultiMedia (WMM), IEEE 802.11e
Security
  • IEEE 802.1X Port Based Network Access Control
  • RFC 2548 Microsoft Vendor-specific RADIUS Attributes
  • RFC 2865 RADIUS Authentication
  • RFC 3394 Advanced Encryption Standard (AES) Key Wrap Algorithm
  • RFC 3579 RADIUS Support For Extensible Authentication Protocol (EAP)
  • RFC 3580 IEEE 802.1X RADIUS Guidelines
  • Access Control Lists (ACLs)
  • Guest VLAN for 802.1x
  • Secure Sockets Layer (SSL)
  • SSHv2 Secure Shell
  • Web Authentication
  • WPA (Wi-Fi Protected Access)/WPA2
IKEv1
  • RFC 3748 - Extensible Authentication Protocol (EAP)

HP 830 Unified Wired-WLAN Switch Uplink Module (JG643A)

HP 830 Unified Wired-WLAN Switch Uplink Module (JG643A)

10GbE uplink for the HP 830 24-Port PoE+ Unified Wired-WLAN Switch


This accessory currently doesn't have any detailed specifications. To learn more contact a HP Networking Expert.

Compatible products

HP X125 1G SFP LC LH40 1310nm Transceiver (JD061A)

A small form-factor pluggable SFP Gigabit LH40 transceiver that provides a full duplex Gigabit solution up to 40km on a single-mode fiber.

Ports

1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)

Connectivity

Connector type: LC
Wavelength: 1310 nm

Physical characteristics

Dimensions: 2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
Full configuration weight: 0.04 lb. (0.02 kg)
Transceiver form factor: SFP

Environment

Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 5% to 85%, noncondensing
Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage relative humidity: 5% to 85%, noncondensing
Altitude: up to 10,000 ft. (3 km)

Electrical characteristics

Power consumption typical: 0.8 W
Power consumption maximum: 1.0 W

Cabling

Cable type:
  • Single-mode fiber optic, complying with ITU-T G.652

Maximum distance:

  • Up to 40km

Fiber type: Single Mode

Compatible products

HP X120 1G SFP LC LH40 1550nm Transceiver (JD062A)

A small form-factor pluggable (SFP) Gigabit LH40 transceiver that provides a full-duplex Gigabit solution up to 40 km on a single mode fiber.

Ports

1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)

Connectivity

Connector type: LC
Wavelength: 1550 nm

Physical characteristics

Dimensions: 2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
Full configuration weight: 0.04 lb. (0.02 kg)
Transceiver form factor: SFP

Environment

Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 0% to 85%
Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage relative humidity: 0% to 85%
Altitude: up to 10,000 ft.

Electrical characteristics

Power consumption typical: 0.8 W
Power consumption maximum: 1.0 W

Cabling

Cable type:
  • Single-mode fiber optic, complying with ITU-T G.652

Maximum distance:

  • Up to 40km

Fiber type: Single Mode

Compatible products

HP X125 1G SFP LC LH70 Transceiver (JD063B)

A small form-factor pluggable (SFP) Gigabit LH70 transceiver that provides a full-duplex Gigabit solution up to 70km on a single-mode fiber.

Ports

1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)

Connectivity

Connector type: LC
Wavelength: 1550 nm

Physical characteristics

Dimensions: 2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
Full configuration weight: 0.04 lb. (0.02 kg)
Transceiver form factor: SFP

Environment

Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 0% to 85%
Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage relative humidity: 0% to 85%
Altitude: up to 10,000 ft. (3 km)

Electrical characteristics

Power consumption typical: 0.8 W
Power consumption maximum: 1.0 W

Cabling

Cable type:
  • Single-mode fiber optic, complying with ITU-T G.652

Maximum distance:

  • 70km

Fiber type: Single Mode

Compatible products

HP X120 1G SFP LC SX Transceiver (JD118B)

A small form-factor pluggable (SFP) Gigabit SX transceiver that provides a full-duplex Gigabit solution up to 550m on a Multimode fiber.

Ports

1 LC 1000BASE-SX port

Connectivity

Connector type: LC
Wavelength: 850 nm

Physical characteristics

Dimensions: 2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
Full configuration weight: 0.04 lb. (0.02 kg)

Electrical characteristics

Power consumption typical: 0.8 W
Power consumption maximum: 1.0 W

Cabling

Maximum distance:
  • FDDI Grade distance = 220m
  • OM1 = 275m
  • OM2 = 500m
  • OM3 = Not Specified by standard

Cable length: up to 550m
Fiber type: Multi Mode

Compatible products

HP X120 1G SFP LC LX Transceiver (JD119B)

A small form-factor pluggable (SFP) Gigabig LX transceiver that provides a full duplex Gigabit solution up to 550m on MMF or 10Km on SMF

Ports

1 SFP 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX)

Connectivity

Connector type: LC
Wavelength: 1300 nm

Physical characteristics

Dimensions: 2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
Full configuration weight: 0.04 lb. (0.02 kg)

Electrical characteristics

Power consumption typical: 0.8 W
Power consumption maximum: 1.0 W

Cabling

Cable type:
  • Either single mode or multimode

Maximum distance:

  • 550m for Multimode
  • 10km for Singlemode

Fiber type: Both

Compatible products

HP RPS1600 Redundant Power System (JG136A)

A-RPS1600 is a cost effective power redundancy solution which can support up to 8 active devices and up to 3200W power per system, 1400W power per port to fixed port switches

Ports

8 redundant power supply ports
Restrictions: two -56V/25A DC(PoE); six -56V/8A DC(non-PoE)

Physical characteristics

Dimensions: 15.63(d) x 17.32(w) x 1.74(h) in. (39.7 x 44 x 4.42 cm)
Weight: 14.11 lb. (6.4 kg)
Full configuration weight: 16.75 lb. (7.6 kg)

Environment

Operating temperature: 14°F to 122°F (-10°C to 50°C)
Operating relative humidity: 5% to 95%
Nonoperating/Storage temperature: -40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage relative humidity: 5% to 95%
Altitude: up to 13,123 ft. (4 km)
Acoustic: Pressure: 53 dB; ISO 7779, ISO 9296

Electrical characteristics

Voltage: 100-120/200-240 VAC
Current: 30/60 A
Idle power: 38 W
Maximum power rating: 3550 W
RPS power: 3200 W
PoE power: 2800 W
RPS: -55 V
PoE: -55 V
Frequency: 50/60 Hz
Notes: Idle power is the actual power consumption of the device with no ports connected.
Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.
With one RPS1600 Power Supply, the PRS1600 Redundant Power System can provide 1600W power output; With two PRS1600 Power Supplies, the output power is 3200W.

Safety

CE Labeled
UL 60950-1
IEC 60950-1
ICES-003
FCC Part 15, Subpart B
EU RoHS Compliant
EN 60950-1/A11
C-Tick
VCCI Class A
ROHS Compliance
EN 300386

Compatible products

HP RPS1600 1600W AC Power Supply (JG137A)

A 1600W-220V / 800W-110V AC Power Supply for the A-RPS1600 Redundant Power System

Physical characteristics

Dimensions: 8.19(d) x 4.96(w) x 1.63(h) in. (20.8 x 12.6 x 4.15 cm)
Weight: 3.02 lb. (1.37 kg)

Environment

Operating temperature: 14°F to 122°F (-10°C to 50°C)
Operating relative humidity: 5% to 95%
Nonoperating/Storage temperature: -40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage relative humidity: 5% to 95%

Electrical characteristics

Voltage: 100-120/200-240 VAC
Current: 15/30 A
Maximum power rating: 1600 W
Frequency: 50/60 Hz
Notes: Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Compatible products

HP 830 Unified Wired-WLAN Switch 12-Access Point E-LTU (JG648AAE)

Incremental add-on license to the HP 830 Unified Wired-WLAN Switch for 12 additional access points


This accessory currently doesn't have any detailed specifications. To learn more contact a HP Networking Expert.

Compatible products

HP 830 Unified Wired-WLAN Switch Series

HP Care Packs for HP Networking

There are currently no care packs

HP Networking Services

Services that add value to your business

The warranties on HP Networking products provide a robust foundation for ongoing network support, but many customers have advanced support needs. Today's enterprise businesses, regardless of their size, are under increasing pressure to reduce the cost and complexity of supporting their network infrastructures. Demand for new services from businesses and their end users is constantly increasing. HP offers an affordable, comprehensive portfolio of networking services for organizations of all sizes. HP has a unique services advantage you can benefit from, and HP is the only vendor in the IT industry that can provide integrated and consistent support for your entire technology infrastructure worldwide, including networking, servers and storage, and imaging and printing, as well as desktop and mobile computing, to help you grow your business with expert support that is affordable, personal, and scaled to your needs. HP Networking's implementation and design centers simplify your network planning, while HP Technology and Enterprise Services deliver choice and flexibility.

HP provides a full range of custom services to meet the end-to-end networking needs of our customers. HP Network Lifecycle Services form the core foundation of network consulting, assessments, planning, design, integration, deployment, and management. They are available as standalone services or can be crafted to deliver solutions across the services portfolio, spanning network performance, network security and risk management, global deployment, data center networking, wireless LAN/mobility, and Unified Communications and Collaboration.

Additional Support and Services

To get more details about the HP Services available in your country, please visit Networking Services

Resources

1 results
No content available for the current selections and/or search text.

Search Hints

  • Text entered will search within the current high-level category (Switches or Wireless for example)
  • Results are based on matches within the title and any product associations
  • The search is not case sensitive
  • Separate terms or phrases with a space, no commas
  • Use quotes to search for an exact phrase. Ex: "converged infrastructure"
  • You may mix and match single terms and phrases. Ex: "converged infrastructure" 5400
Analyst Reports  (0)
Type
Size Date
Brochures  (0)
Type
Size Date
Case Studies  (0)
Type
Size Date
Configuration  (0)
Type
Size Date
Diagram Tools  (0)
Type
Size Date
Firmware & Release Notes  (0)
Type
Size Date
Installation  (0)
Type
Size Date
Planning & Design  (0)
Type
Size Date
Product Specifications / FAQs  (0)
Type
Size Date
Programming & Development  (0)
Type
Size Date
Related Links  (0)
Type
Size Date
Safety & Regulatory  (0)
Type
Size Date
Service & Maintenance  (0)
Type
Size Date
User Guides  (0)
Type
Size Date
White Papers  (0)
Type
Size Date
Search results (0) Type Size Date